MSAN ZTE ZXMSG 5200

ZXMSG 5200

Multiplex Service Gateway

Configuration Manual

Version: V3.2

Using SIP Protocol

1.       Modify License

Before begin the integration, first we have to modify the license.dat;

1.1.  Upload the license.dat to your laptop

Open telnet from command prompt;

ZXAN#dir cfg

Directory of flash:/cfg

            attribute   size       date         time        name

1           drwx        16384      APR-17-2013  16:50:20    .

2           drwx        16384      JAN-01-1970  00:00:00    ..

3           -rwx        4096       APR-17-2013  13:50:12    nvram.dat

4           -rwx        900        NOV-08-2012  14:37:56    license.dat

5           -rwx        5426       APR-17-2013  16:50:20    startrun.dat

ZXAN#con t

ZXAN(config)# interface mng1

ZXAN(config-if)# boot-server 136.1.1.10  ------- base on clien IP

ZXAN(config-if)# boot-user zte

ZXAN(config-if)# boot-password zte

1.2.  Open WFTP, set username and password by zte and set Home directory as well

ZXAN#upload cfg license.dat

1.3.  Modify the license.dat as following (open file with *WordPad)

                   1=1   modify   1=0

    7=0   modify   7=1

       

Save and close the file.

1.4.  Download the license.dat to GISB again.

ZXAN#download cfg license.dat

ZXAN#reboot

2.       Delete Previous Data and Configuration

ZXAN#delete v0100 *.*

ZXAN#delete v0101 *.*

ZXAN#delete cfg startrun.dat

ZXAN#reboot

3.       Configuration

3.1.   Configuring a Rack

ZXAN#configure terminal

Enter configuration commands, one per line.

End with CTRL/Z.

ZXAN(config)#

Configure the control rack.

ZXAN(config)#add-rack rackno 1 racktype MSAG

3.2.   Configuring a Master Shelf and Subordinate Shelf

ZXAN(config)#add-shelf rackno 1 shelfno 1 shelftype MBSL_CTL

ZXAN(config)#add-shelf rackno 1 shelfno 2 shelftype MBSL_EX connectid 1  -> if have subordinate shelf

3.3.   Configuring Card

Configing the card based on the modules are installed on the shelf

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 1 POWER

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 3 GELCA

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 4 GELCA

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 5 GELCA

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 6 GELCA

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 7 GPNI

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 8 GPNI

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 16 TSLCE

ZXAN(config)#add-card rackno 1 shelfno 1 slotno 17 POWER

3.4.   Configuring Sub-Card

To configure a VoIP sub-card in sub-card 2 slot 9 and 10, perform the following commands:

ZXAN(config)#del-subcard slotno 9 subcard 2

ZXAN(config)#add-subcard slotno 9 subcardno 2 VOIP

ZXAN(config)#add-subcard slotno 10 subcardno 2 VOIP

3.5.   Configuring VLAN

ZXAN(config)#interface pni-gei_1/8/1

ZXAN(config-if)#switchport mode hybrid

ZXAN(config-if)#switchport vlan 1048 tag     ----> signaling VLAN example

ZXAN(config-if)#switchport vlan 2048 tag     ----> media VLAN example

ZXAN(config-if)#switchport vlan 3136 tag               ----> data VLAN example

ZXAN(config-if)#switchport vlan 161 tag     ----> OAM VLAN example

ZXAN(config-if)#switchport vlan 110 tag      ----> IPTV VLAN

ZXAN(config-if)#switchport vlan 111 tag      ----> IPTV VLAN

ZXAN(config-if)#no shutdown

ZXAN(config-if)#exit

3.6.  Configuring VoIP Service (SIP)

3.6.1.         Configure the Control Port

ZXAN(config)#msag

ZXAN(config-msag)#ctrlport add 15 5060

3.6.2.         Configure the MGC

ZXAN(config-msag)#mgc add 1 172.27.53.5 port 5060 type 2

3.6.3.         Configure the MG

ZXAN(config-msag)#mg add 1 1 domain-name telkom.net.id protocol-type 3 port 5060

3.6.4.         Configure the SIP Proxy Server

ZXAN(config-msag)#sip proxy-server add 1 5060 1 ProxyIP 172.27.53.5

3.6.5.         Configure the SIP User Agent

ZXAN(config-msag)#sip user-agent add 1 1 domname telkom.net.id

3.6.6.         Configure the Media and Signalling IP address

ZXAN(config-msag)#voip interface add ctrl-ip 172.24.79.7 ctrl-mask 255.255.255.192 media-ip 172.24.48.7media-mask 255.255.255.192

ZXAN(config-msag)#voip route add 172.24.79.1destipaddr 172.27.53.5 submask 255.255.255.192 type 2

ZXAN(config-msag)#voip route add 172.24.48.1 type 1

3.6.7.         Configure the SIP number analysis table

ZXAN(config-msag)#digitmap add 1 SIPDM digit-map ExxEx.Ex.F|x|xF|ExxF|3F|ExxE|EE0x|FxxF|x.|xxxxxx|xxxxxxxxxxxxx|ExxE85xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]x|04[2-9]xxxxxSxxx|85xxxxx mgid 1 servicetype 2

3.6.8.         Configure the SIP User

Digitmapname based on the name we use when we creat SIP number analysis table and password according to information from IMS. Usually each number has its own password.

ZXAN(config-msag)#sip user add 3 begin-index 1 num 1 +622129875040 digitmapname SIPDM password 1A2B3C4D5E authUsername +622129875040 digitlen 0 type 3

3.6.9.         Configure the SIP UserID

ZXAN(config-msag)#sip userid add 3 begin-index 1 num 1 +622129875040 digitlen 0 type 3

3.6.10.      Configure the RTP Resource

ZXAN(config-msag)#rtp terminationid add RTP/ 240 mgid 1 type 2 begin-no 0

3.6.11.      Configure the internal media flow route

ZXAN(config-msag)#media-nat add 9 1 9 5 5 172.24.48.7 10000

3.7.  Configuring VoIP Service (H248)

3.7.1.         Configure the MGC

ZXAN(config-msag)#mgc add 1 172.28.5.7 port 2944 type 2

ZXAN(config-msag)#mgc add 2 172.28.4.7 port 2944 type 2

ZXAN(config-msag)#mg add 1 1 mgcid2 2 port 2944

3.7.2.         Configure the Media and Signalling IP address

ZXAN(config-msag)#voip interface add ctrl-ip 172.24.79.7 ctrl-mask 255.255.255.192 media-ip 172.24.48.7media-mask 255.255.255.192

ZXAN(config-msag)#voip route add 172.24.79.1destipaddr 172.28.5.7 submask 255.255.255.192 type 2

ZXAN(config-msag)#voip route add 172.24.48.1 type 1

3.7.3.         Configure TID (H248)

ZXAN(config-msag)#slc terminationid add rackno 1 shelfno 1 3 begin-index 1 num 32 A begin-no 0 type 2 mgid 1

ZXAN(config-msag)#slc terminationid add rackno 1 shelfno 1 4 begin-index 1 num 32 A begin-no 32 type 2 mgid 1

ZXAN(config-msag)#slc terminationid add rackno 1 shelfno 1 5 begin-index 1 num 32 A begin-no 64 type 2 mgid 1

ZXAN(config-msag)#slc terminationid add rackno 1 shelfno 1 6 begin-index 1 num 32 A begin-no 96 type 2 mgid 1

ZXAN(config-msag)#slc terminationid add rackno 1 shelfno 1 11 begin-index 1 num 32 A begin-no 128 type 2 mgid 1

3.8.  Configuring Media IP, Signaling IP, and Management IP

3.8.1.         Configure Media IP

ZXAN(config)#vlan 2040

ZXAN(config-vlan)#voip-bind

ZXAN(config-vlan)#exit

ZXAN(config)#interface vlan 2040

ZXAN(config-if)#ip address 172.24.48.7 255.255.255.192          

ZXAN(config-if)#exit

3.8.2.         Configure Signalling IP

ZXAN(config)#vlan 1040

ZXAN(config-vlan)#voip-ctrl

ZXAN(config-vlan)#exit

ZXAN(config)#interface vlan 1040

ZXAN(config-if)#ip address 172.24.79.7 255.255.255.192          

ZXAN(config-if)#exit

3.8.3.         Configure Management IP

ZXAN(config)#vlan 161

ZXAN(config-vlan)#exit

ZXAN(config)#interface vlan 161

ZXAN(config-if)#ip address 172.24.112.7 255.255.255.192          

ZXAN(config-if)# exit

Use the ip route command to set default gateway, if the NM server and ZXMSG 5200are not in the same network segment.

ZXAN(config)# ip route 172.27.53.0 255.255.255.192 172.24.79.1

ZXAN(config)# ip route 172.28.1.0 255.255.255.192 172.24.112.1

ZXAN(config)#ip route 0.0.0.0 0.0.0.0 172.24.112.1

3.9.  Set SIP Capability

At MSAN the SIP capability have to modify,

For IMS Huawei do not Support Timer, so at MSAN we have to disable Support Timer,

ZXAN(config-msag)#sip capability modify SPTIMER 0

For both IMS Ericsson and Huawei support 100REL, so enable support 100REL,

ZXAN(config-msag)#sip capability modify SP100REL 1

AuthorisationUsername with Domain is enable for both Huawei and Ericsson IMS,

ZXAN(config-msag)#sip capability modifyAuthUsernamewithDom 1

For Fax service, Huawei IMS using FaxoverIP T30

ZXAN (config-msag)#sip capability modify FaxOverIp1 ?

<0-2>  1:T30,2:T38,0:NULL

ZXAN (config-msag)#sip capability modify FaxOverIp1 1

3.10.           Configuring IPTV Service

ZXAN(config)#igmp enable

ZXAN(config)#igmp mvlan 110

ZXAN(config)#igmp mvlan 110 group 239.1.1.1 to 239.1.1.254

ZXAN(config)#igmp mvlan 110 group 239.1.2.1 to 239.1.2.254

ZXAN(config)#igmp mvlan 110 source-port pni-gei_1/8/1

ZXAN(config)#igmp mvlan 110 receive-port adsl_1/3-6/1-32

3.11.           Configuring ADSL Port

ZXAN(config)#interface adsl_1/3-6/1-32

ZXAN(config-if)# atm pvc 1 vpi 8 vci 88

ZXAN(config-if)# pvc 1 enable

ZXAN(config-if)# pvc 2 enable

ZXAN(config-if)# pvc 3 enable

ZXAN(config-if)# switchport mode hybrid pvc 1

ZXAN(config-if)# switchport default vlan 111 pvc 1

ZXAN(config-if)# switchport vlan 110 untag pvc 1

ZXAN(config-if)# switchport mode hybrid pvc 2

ZXAN(config-if)# switchport default vlan 3136 pvc 2

ZXAN(config-if)# port-location format dsl-forum pvc 1

ZXAN(config-if)# port-location format dsl-forum pvc 2

ZXAN(config-if)# pppoe-plus enable pvc 2

ZXAN(config-if)# igmp version v2 pvc 1

ZXAN(config-if)# adsl profile DEF1M.PRF

3.12.           Fax Configuration (H248)

ZXAN(config-msag)#rtp voip-parameter dtmf dtmfrelaymode 1

ZXAN(config-msag)#rtp voip-parameter dtmf dtmfpayload 97

ZXAN(config-msag)#rtp voip-parameter fax-modem faxmode 11

ZXAN(config-msag)#rtp voip-parameter fax-modem modemmode 11

ZXAN(config-msag)#tone fax-event 1 answi-tone 1

ZXAN(config-msag)#tone fax-event 1 answo-tone 1

ZXAN(config-msag)#tone fax-event 1 v21-flags-tone 1

ZXAN(config-msag)#rtp voip-parameter rxhandle mindelay 20 maxdelay 120 nomdelay 20

ZXAN(config-msag)#mg capability 1 fax-pri1 2 fax-pri2 1

3.13.           Configuring Phone Features

For all the features, it provide by IMS, at MSAN will make some change at parameter.

3.13.1.      Call wait

For call wait feature the configuration execute under 9999 port.

Open telnet;

[ROS10]:callwaitno180=0

callwaitno180 = 0x216b568: value = 0 = 0x0

For callwait service, callwait parameter have to be set

ZXAN(config-msag)#sip accesscode add mgid 1 id 1 2 (id 1 is accesscode for callwait)

For activation dial *43# and deactivation #43#.

Scenario; B with callwait feature, A call B, and B busy now

                  C call B, callwait tone on, B accept C call by dial “Flash+2”

3.13.2.      Call Forward

Only for call forward conditional busy have to change the user paramenter.

a.        Call Forward Unconditional

For activation dial *21*(phone number to forward)# and deactivation #21#.

Scenario; B with call forward unconditional feature, A call B,

        A will forwarding to C unconditional

b.       Call Forward Conditional Busy

For call forward conditional busy, user have not support multi call

ZXAN#show msag sip user 3

rack:1

shelf:1

slot:3

index:1

sip-digits: +622129860005

groupid:0

password:123456

dstngring:15

hotlinetype:0

hotlinenum:

userid: +622129860005

digitmap:SIPDM

username: +622129860005

enableflag:1

sessionlimit:0    ---------- > user support multi call

disable multi call by modify the session limit

ZXAN(config-msag)#sip user mod 3 begin-index 1 num 1 sessionlimit 1

For activation dial *67*(phone number to forward)# and deactivation #67#.

Scenario; B with call forward conditional busy feature. A call B, B busy now

        A forwarding to C because B busy.

c.        Call Forward Conditional No Reply

For activation dial *61*(phone number to forward)# and deactivation #61#.

Scenario; B with call forward conditional no reply. A call B

        A forwarding to C because B not reply.

3.13.3.      Three Party

For three party service, all the three party parameters have to be set.

ZXAN(config-msag)#sip servcode add 0 3F (0 mean type conference, F mean “#”)

ZXAN(config-msag)#sip accesscode add mgid 1 id 6 3F (id 6 is accesscode for threeparty)

ZXAN(config-msag)#sip capability mod ThreptySvr jk1magcf01conf

Show the configuration

ZXAN(config)#sho msag sip servcode

mgid:1

type: Conference

sip service code:3F

ZXAN(config)#sho msag sip accesscode

mgid:1

id: 6

sip access code:3F

Scenario; B with three party feature, B calling A, A on hold now and B calling C

                  B press “FLASH+3+#”, A and B and C join conference.

Make sure that digitmap for 3# is available. Note: # to be symbolized by F

ZXAN#sho msag digitmap

digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85

xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]

x|04[2-9]xxxxxSxxx|85xxxxx

3.13.4.      HotLine

HotLine services, both immediate and delay, parameter change under 9999 port.

·      Execute command:HotLineServCode

[ROS10]:HotLineServCode

HotLineServCode = 0x216b568: value = 0 = 0x0 (blue color show hot line service code)

·      Display service code by execute command: d 0x216b568

[ROS10]:d 0x216b568

0216b560:  0000 0000 0000 0000   *     ......*

0216b570:  0000 0000 0000 0000 0000 0000 0000 0000   *................*

0216b580:  0000 0000 0000 0000 0000 0000 0000 0000   *................*

0216b590:  0000 0000 0000 000b 0000 0001 0000 0000   *................*

0216b5a0:  0000 0000 0000 0005 5a54 4500 0000 0000   *........ZTE.....*

0216b5b0:  0000 0000 0000 0000 0000 0000 0000 0001   *................*

………………………………………..

value = 21 = 0x15

·      Modify service code by execute command: m 0x216b568

[ROS10]:m 0x216b568

It will output '0000-...',then type 0302(No display,just input),

0216b568:  0000-0302

The'0000-' will display again,and then type 0100,

0216b56a:  0000-0100

Input .(dot) after display '0000-'.

0216b56c:  0000-.

After all the modify, it will show;

value = 1 = 0x1

·      Disply service code again after modify

[ROS10]:d 0x216b568

0216b560:                    0302 0100 0000 0000   *     ......*

0216b570:  0000 0000 0000 0000 0000 0000 0000 0000   *................*

0216b580:  0000 0000 0000 0000 0000 0000 0000 0000   *................*

0216b590:  0000 0000 0000 000b 0000 0001 0000 0000   *................*

0216b5a0:  0000 0000 0000 0005 5a54 4500 0000 0000   *........ZTE.....*

0216b5b0:  0000 0000 0000 0000 0000 0000 0000 0001   *................*

……………………………………………

value = 21 = 0x15

It should be successful if it show 0302 0100.

Make sure the number that we created already provisioning by IMS MTAS. IMS will send message on notify section when we registered the user number.

a.        HotLine Immediate

For immediate hotline, will get message like below:

<?xml version="1.0" encoding="UTF-8"?><simservs xmlns="http://uri.etsi.org/ngn/params/xml/simservs/xcap"><dial-tone-management><no-dialling-behaviour>immediateCallSetup</no-dialling-behaviour><centrex-info/></dial-tone-management></simse

Scenario: A with hot line immediate feature, A pickup handset immediate calling B

b.       HotLine Delay

For delay hotline, will get message like below:

<?xml version="1.0" encoding="UTF-8"?><simservs xmlns="http://uri.etsi.org/ngn/params/xml/simservs/xcap"><dial-tone-management><no-dialling-behaviour>deferredCallSetup</no-dialling-behaviour><centrex-info/></dial-tone-management></simser

For activation dial *52*B number#

Scenario: A with hot line delay feature, A pickup handset after couple seconds, A calling B

3.13.5.      Abbreviated

For abbreviated feature, make sure the digitmat for abbreviate is available. For example by dialing “**03” will connecting to specified number, so the digitmap format will be “EE03”.    Note: * to be symbolized by E.

ZXAN#sho msag digitmap

digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85

xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]

x|04[2-9]xxxxxSxxx|85xxxxx

3.13.6.      Keyboard

Keyword feature depends on digitmat format. The form for keyword feature is *34*password*class#

Scenario: A dial *34*1234*1#. So the password is “1234” and class is “1”

Note; Class (0=block all, 1=local only, 2=interlocal, 3=international call)

ZXAN#sho msag digitmap

digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85

xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]

x|04[2-9]xxxxxSxxx|85xxxxx

3.13.7.      Fax

Both Huawei and Ericsson IMS do not support T38 and VBD for Fax service, disable fax priority 1 and fax priority 2

ZXAN(config-msag)#mg capability 1 fax-pri1 0

ZXAN(config-msag)#mg capability 1 fax-pri2 0

3.13.8.      EDC

For EDC just make sure the digitmap is available. For example, B*A EDC server number usually depend on 13 digits. So the digitmap consists of 13 digits.

ZXAN#sho msag digitmap

digitmap:ExxEx.ExF|2|3F|E43F|xF|ExxE|EE0x|ExxF|FxxF|xxxxxx|xxxxxxxxxxxxx|ExxE85

xxxxxF|ExxE08xxxxxxxxxF|0[2-9]xxxxxSxxxxxx|03[1-9]xxxxxSxxx|[2-9]xxxxSxxx|1[2-9]

x|04[2-9]xxxxxSxxx|85xxxxx

Selamat Mencoba semoga berhasil !!!!